Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Kent, WA
Gate repair in Kent, WA means dealing with a specific mix of weather and property layouts: rain-soaked electronics, rust on steel frames, and plenty of long gravel driveways where the gate sits far from the house. Most Kent gate problems we see fall into three buckets: a gate that won’t open, a gate that won’t stay closed, or an opener that runs but doesn’t move the gate. Calder Gate Repair handles all three, and we give you a written price before any work starts. Call (903) 417-0793 and a live person answers, 24/7.
Why Kent Homes Are Different
Kent’s combination of wet winters and older East Hill neighborhoods shapes almost every gate job we do here. Moisture gets into control boards and limit switches faster than in drier parts of the Puget Sound region, and steel gates on properties built in the 1970s and 80s often show rust at the hinge welds before the opener itself fails. Down in the Kent Valley, long driveways off 104th and 132nd mean opener range and signal interference are common issues, so we test antenna placement carefully. On the West Hill side, some HOAs in the newer developments require gate styles and colors to match approved specs, which we can work with on any repair or replacement. And because a lot of Kent homes sit on sloped lots, we routinely adjust gate travel paths so wheels and hinges don’t bind against grade changes.
One more Kent-specific note: prevailing wind off the valley floor pushes gates hard against their stops. That constant pressure wears out the limit switch faster than you’d expect, and it’s often the reason a gate stops mid-swing or refuses to close fully on breezy days.
Our Main Kent Services
These are the three calls we get most from Kent homeowners, each with its own dedicated page and its own pricing breakdown.
Gate Repair in Kent
A sagging gate in Kent is usually a hinge or wheel problem before it becomes an opener problem. We see a lot of dual-swing gates on older East Hill properties where the original posts have shifted in wet soil, throwing the whole gate out of square. Calder’s gate repair work covers bent or rusted hinges, cracked welds, gate wheels worn flat, and frame straightening. We also handle gates that scrape the driveway after frost heave settles. If your gate still moves but fights you or makes noise, start with Gate Repair in Kent and we’ll tell you what’s actually wrong, in plain English, before we touch a bolt.
Electric Gate Repair in Kent
Kent’s damp climate is tough on electric gates. Water intrusion into the control box and corroded wiring connections are the two most common failures we diagnose here, especially on properties where the gate sits low and catches runoff. Our electric gate repair covers the full electrical side: control boards, safety sensors, keypads, intercom wiring, and the power run from the house to the gate. We carry sealed connectors and weatherproof enclosures on our trucks specifically because Kent jobs need them. When the gate won’t respond at all, or trips the breaker, head to Electric Gate Repair in Kent for the full breakdown.
Gate Opener Repair in Kent
When the opener hums but the gate doesn’t move, or the remote only works from ten feet away, it’s an opener issue, not a gate issue. We repair arms, gearboxes, limit switches, and receiver boards on all the major brands, and because so many Kent driveways run long, we often relocate antenna modules or add signal repeaters. Calder technicians are factory-familiar with Linear, Viking, Ghost Controls, and DoorKing, among others. If your remote’s range has dropped or the opener cycles without moving the gate, the full detail is on Gate Opener Repair in Kent.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Kent
We work on Linear, Viking, Ghost Controls, and DoorKing openers every week in Kent, and we carry common replacement parts for all four brands in our local trucks. That means most opener repairs finish in a single visit instead of waiting a week for a part to ship. See everything we cover on our brands page.
Pricing for Gate Company in Kent, WA
| Service | Typical range in Kent |
|---|---|
| Gate opener motor replacement (parts + labor) | $400 – $850 |
| Control board replacement | $250 – $550 |
| Limit switch replacement | $120 – $260 |
| Gate hinge repair (single hinge, welded) | $90 – $220 |
| Gate wheel replacement | $80 – $180 per wheel |
| Keypad installation or replacement | $180 – $380 |
| Safety sensor realignment or replacement | $100 – $250 |
| Remote programming or replacement | $60 – $150 |
| Full-service diagnostic visit (waived with repair) | $0 – $90 |
| Gate opener installation (new unit, standard arm) | $750 – $1,800 |
What pushes the price up in Kent is moisture damage: a control board that’s been wet for months may also need a new enclosure and rewired connections, not just a board swap. Same with rusted hinges on older steel gates, the labor goes up when the metal around the hinge needs reinforcement. Whatever we find, the price is written down and agreed to before any work starts, and the invoice never lands above that number.
Neighborhoods We Serve in Kent
We run calls all over Kent daily, and our typical arrival window for gate repairs in the area is same-day or next morning, depending on when you call. Here are a few of the neighborhoods we cover regularly:
- East Hill
- West Hill
- Panther Lake
- The Valley (downtown Kent)
- Woodmont / East Hill border
Service Area – Cities Near Kent
While this page focuses on Kent, our crews also cover the surrounding communities. If you’re up in Renton, WA, over in Auburn, CA, west toward Federal Way, WA, or out past the valley in Maple Valley, WA, the same written-price guarantee and 365-Day Done Right Promise apply.
Serving Kent, WA - Our Local Coverage Area
We’re based in the Kent area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Kent
Most Kent gate repair calls get a same-day or next-morning arrival window. When you call (903) 417-0793, a live person gives you a trackable arrival time, not a four-hour window. If we’re already in your area, we can often be there within a few hours. For urgent failures where a gate is stuck open, call and we’ll tell you our soonest slot honestly.
For repairs that keep the existing gate style and color, Kent HOAs generally don’t require prior approval, especially in newer West Hill developments where the style rules mainly apply to full replacements. If your community has an architectural review process and you’re replacing the gate rather than repairing it, we’ll flag that before you commit. The repair itself doesn’t wait on HOA paperwork.
Yes. Long driveways in the Kent Valley are routine for us, and we test opener range and signal strength as part of any repair. If your gate sits far from the house and the remote has been getting weaker, we’ll check antenna placement and interference before assuming the opener itself is failing. The fix is often simpler and cheaper than a full opener replacement.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Kent Customers Say
"Safety sensors realigned. Works fine. Photo eyes were dirty and out of line. Gate now stops when it should."
- Raul A."Booked online. The tech texted his ETA and arrived on time. Gate opener was dead; he replaced the control board and tested the sensors."
- Terry W."Booking was easy and the job was done quickly."
- Seth R.