Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Burbank
Gate repair in Burbank typically runs $180 to $340 for hinge and alignment work, and $240 to $450 for opener and circuit board repairs before parts. Most jobs are done in one visit. We’re Calder Gate Repair, and we work throughout Burbank, from the Rancho district up toward the Verdugo Hills. If your gate is sagging, stuck, or refusing to open, call us at (903) 417-0793 and a real person answers, day or night. We’ll give you a written price before anything gets unbolted.
Why Calder Gate Repair Is Burbank’s Preferred Gate Repair Company
Burbank homeowners keep calling us back because we treat a gate like a safety device, not a weekend project. Our technicians are background-checked, arrive in uniform, and send a live trackable arrival time so you’re not stuck waiting through a four-hour window. Every repair carries our 365-Day Done Right Promise: if the repair fails within a year, we come back and fix it at no charge. That’s written on every invoice.
We know the streets here. Magnolia Park’s 1940s bungalows, the hillside lots along Walnut Avenue, the gated driveways off Glenoaks – each one presents a different gate geometry and wear pattern. Our Gate Repair team has seen hinge posts rotted from decades of irrigation runoff and operators burnt out from running against a binding track. Nico Alvarez, who leads Calder Gate Repair, insists on one standard: the gate leaves working correctly, tested through a full open-close cycle, before we hand it back to you.
Dispatch and scheduling are coordinated from our Los Angeles office, but crews serve Burbank locally, which means we can usually reach a home near the Burbank Town Center or up near Brace Canyon Park the same day you call.
Wrought Iron Gate Repair in Burbank
Wrought Iron Gate Repair in Burbank usually involves three things: failed hinge welds, posts that have shifted out of plumb, and operator motors that burned out trying to move a gate that no longer swings freely. On a hillside driveway off Olive Avenue, even a quarter inch of post lean translates into a gate that drags and strains the opener. Typical wrought iron repair work in Burbank runs $180 to $340 for hinge replacement and post reset, with full weld repairs on cracked rails running higher depending on how far the rust has spread.
Post Resetting and Footing Work
A sagging iron gate is almost never a hinge problem by itself. In most cases the hinge post footing has shifted or rotted below grade. We excavate, reset the post in fresh concrete, and brace it true before re-hanging the gate, so the fix lasts instead of sagging again in six months.
Weld Repairs and Rust Treatment
Burbank’s summer heat and occasional Santa Ana winds dry out iron fast, but winter rains get into hairline cracks and start rust bleeding through the paint. We grind back to clean metal, weld the cracked rail or hinge plate, then prime and paint the repair so it doesn’t show.
Metal Gate Repair in Burbank
Metal Gate Repair in Burbank covers a lot of ground: steel tube-frame gates on the flats, aluminum drive gates in the hills, and heavy commercial-style metal gates on some of the larger Rancho properties. Most metal gate repairs in Burbank run $200 to $380 for structural work, with operator replacement on top of that if the motor died. The key difference between a good repair and a repeat failure is whether the gate’s geometry gets checked, not just the broken part swapped.
Rack and Pinion Alignment
Slide gates on sloped driveways, common in the Burbank hills above Kenneth Road, wear rack and pinion teeth unevenly when the rail isn’t matched to the actual grade. The gate binds mid-travel, the motor overdraws, and either the breaker trips or the safety reversal kicks in. We re-align the rack to the driveway’s true slope and set the travel limits correctly.
Safety System Retrofits
Older Burbank driveway gates sometimes lack the UL 325 entrapment protection now required. We fit or recalibrate photoelectric sensors and contact safety edges, then run through the full reversal test cycle. The gate should stop and reverse on contact, not keep pushing.
Trusted Brands We Service in Burbank
We’re factory-familiar with the gate openers Burbank homeowners actually have installed: Viking, Ghost Controls, DoorKing, and Elite, among the nine major brands our technicians train on. That matters because a DoorKing board trouble code and a Ghost Controls fault readout mean different things, and misdiagnosing one wastes a service call. We keep common replacement parts in local stock, so we’re not waiting on a distributor when your gate is stuck open. If your Viking opener died after a power surge near the Rancho, we can usually diagnose it in the first visit and give you the written price on the spot.
Common Gate Repair Problems We See in Burbank Homes
- Hinge post rot or footing shift: Older Burbank bungalows, especially in Magnolia Park, often have hinge posts set in footings that have been undermined by decades of sprinkler runoff. The post leans, the gate drags, and the opener motor burns out trying to compensate.
- Loop detector and safety photocell misalignment: Driveway resurfacing or new landscaping shifts the in-ground loop or knocks the photo eyes out of line. The result is a gate that reverses for no reason or refuses to close, which is exactly what happened on North Hollywood Way near Lincoln Street when a LiftMaster slide gate kept stopping halfway and reversing.
- Rack and pinion wear on sloped driveways: Homes in the hillside streets above Olive and Alameda frequently have gates where the rack was installed to spec for level ground, but the driveway drops several inches over the gate’s travel. The gate stalls mid-cycle, and the motor strains until something gives.
- Opener burnout from a binding gate: Most opener failures aren’t electrical. A gate that binds because of a shifted post or a worn rack draws more current, overheats the motor, and eventually fries the control board. Fixing the mechanical drag first is what stops the next board from dying.
Pricing for Gate Repair in Burbank, CA
What you’ll pay for gate repair in Burbank depends on the failure, not the contractor’s mood. Hinge and post work typically runs $180 to $340. Opener repair, including circuit board diagnostics and replacement, runs $240 to $450 before parts. Full rack and pinion replacement on a slide gate starts around $500 and climbs with gate length. Wrought iron weld repairs run $200 to $380 depending on how many rails are cracked. We always give a written price before any work starts, and that number doesn’t change when the invoice arrives. Call (903) 417-0793 for a free estimate – a live person answers 24/7 and can schedule your visit.
We Also Serve Cities Near Burbank
Calder Gate Repair handles Gate Repair in Burbank and the surrounding area, including Glendale, West Hollywood, Altadena, and Beverly Hills. If your property is outside central Burbank, we’ll still dispatch a technician to you with a live arrival time and the same written-price guarantee.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Burbank
Because the hinge post footing has shifted or rotted below grade, not because the hinge bolts are loose. Burbank’s older bungalow driveways, particularly in Magnolia Park and the Rancho area, often have posts set in shallow concrete that has been undermined by irrigation water. Tightening the hinges just pulls the post further out of plumb. The correct fix is to reset the post in a new footing and re-hang the gate true. Call (903) 417-0793 and we’ll assess the footing before quoting hinge work.
Yes. Every automatic gate operator in Burbank must comply with UL 325, which requires entrapment protection such as photoelectric sensors or contact safety edges, plus a functioning reversal mechanism. Older gates that predate the standard often get skipped during repairs by less thorough technicians. We test the full reversal cycle on every job and won’t hand back a gate that keeps pushing against resistance.
Yes, and that’s a large part of our work in the Burbank hills. Sloped driveways change the effective load on the gate operator, and if the rack and pinion or hinge geometry isn’t set to the actual grade, the gate binds and the motor stalls. We re-align the track and posts to the real slope, then set travel limits and safety sensors for that specific install. The repair is priced before we start, so the slope doesn’t add surprise charges.
A proper installation in Burbank includes the gate plus its groundworks and electrical: post footings dug and set to the slope, conduit for the operator power run, safety photocells or contact edges wired in, the operator motor and its control board, and full travel-limit and reversal testing. Skipping any of those is how you end up with a gate that works for six months and then fights you. We quote the complete scope in writing, so you know what’s included before anything gets ordered. Call (903) 417-0793 for a free measure and written price.
Most repairs, hinge resets, opener replacements, safety sensor fixes, are completed the same day we arrive. Installations are measured and scheduled, not rushed: depending on the gate size, post work, and power run, a full install in Burbank usually takes one to three days on-site, with the written price and schedule agreed before we start. We never promise same-day turnaround on an installation because doing it properly means pouring footings and letting them set.
If your gate is down in Burbank, call (903) 417-0793 now. A live person answers, we’ll give you a trackable arrival window, and you’ll have a written price before the first bolt comes out.
Written by Nico Alvarez, Owner at Calder Gate Repair, serving Burbank gate repair needs with the 365-Day Done Right Promise.