Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Angleton, TX
Gate repair in Angleton, TX usually comes down to one of three jobs: a gate that won’t open, a motor that burned out, or a hinge that finally gave up in the Gulf Coast humidity. Most repairs around here run $180 – $340 before parts, and we can usually have a technician out the same day you call. Calder Gate Repair is the dedicated gate repair specialist inside the Relay Home Co. family, and every job starts with a written price before a single bolt gets turned. Call (903) 417-0793 and a live person answers, 24/7.
Why Angleton Homes Are Different
Angleton sits close enough to the Gulf that the air itself is hard on gate hardware. Salt and moisture work their way into opener circuit boards, corrode limit switches, and rust out hinge pins faster than almost anywhere inland. We regularly see gates that look fine from the curb but have wiring that’s green with corrosion inside the conduit. Homes here run the range from 1970s ranch-style properties with original wrought iron to newer construction with powder-coated aluminum, and the repair approach changes depending on which one you own.
Soil movement is another factor. Brazoria County clay shifts with every wet-dry cycle, which means gate posts settle and the gate drifts out of square. When a gate starts dragging on the driveway or the latch won’t line up, it’s usually not the opener’s fault – it’s the ground under the post. We check alignment before we ever start swapping parts, because fixing the motor without fixing the post means you’ll call us again in six months. Angleton homeowners also deal with HOA requirements in several of the newer subdivisions, and a gate that won’t close properly can turn into a letter from the association pretty quickly.
Our Main Angleton Services
Most calls we get in Angleton fall into one of three categories. Here’s what each one involves and where to find the full breakdown.
Gate Repair in Angleton
Gate repair covers the physical side: hinges, posts, welds, sagging frames, and latches. In Angleton, the biggest culprit is usually corrosion. A gate that’s been through a few hurricane seasons and a dozen hard rainstorms will start binding at the hinges, and once it binds, the opener has to work twice as hard until something fails. We replace hinge pins, reinforce sagging corners, and re-square posts that have shifted in the clay soil. If the frame itself is cracked, we’ll tell you before we touch anything and give you a written price to fix it right. Gate Repair in Angleton.
Electric Gate Repair in Angleton
Electric gate repair is what you need when the gate has power but isn’t behaving: it won’t open all the way, stops halfway, reverses for no reason, or trips the breaker. Near the coast, we see a lot of failures caused by moisture in the junction boxes and photo-eye sensors. The salt air eats through wire nuts and terminal connections faster than you’d believe. We trace the circuit, find the weak connection, and seal everything properly so it stays dry through the next storm season. Electric Gate Repair in Angleton.
Gate Opener Repair in Angleton
Gate opener repair focuses on the motor, control board, and remote system. The most common Angleton call here is an opener that hums but doesn’t move, or a remote that stopped working after a power surge. Summer thunderstorms knock out control boards with some regularity, and when the humidity is high, capacitor failures spike. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule openers, and we carry the most common boards and capacitors stocked locally so we’re not always waiting on a part shipment. Gate Opener Repair in Angleton.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Angleton
We’re factory-familiar with every major gate opener brand you’re likely to have, including FAAC, BFT, Linear, and Viking. We keep the most common replacement boards, sensors, and remotes stocked locally so a typical Angleton repair doesn’t wait on a warehouse. See our brands for the full list of what we service.
Pricing for Gate Company in Angleton, TX
These are the prices you can expect for gate work in Angleton. Every price is quoted in writing before work starts, so the number on the invoice is the number you agreed to.
| Service | Typical range in Angleton |
|---|---|
| Gate and fence gate repair, general | $180 – $340 |
| Complete gate opener replacement | $600 – $950 |
| New gate opener installation | $950 – $1,500 |
| Gate opener gear or sprocket replacement | $180 – $290 |
| Gate opener limit switch adjustment or replacement | $140 – $240 |
| Sliding gate v-wheel or roller replacement | $160 – $320 |
| Dual leaf gate repair | $300 – $600 |
| Solar gate opener repair | $180 – $400 |
Heavy corrosion from the Gulf air is the most common thing that pushes an Angleton quote toward the top of a range, especially when wiring and connectors need to be replaced along with the main part. You’ll see the full price before we start, and if the repair fails within 365 days, Calder Gate Repair comes back at no charge under our 365-Day Done Right Promise.
Neighborhoods We Serve in Angleton
We cover the entire Angleton area, from the older neighborhoods near downtown to the newer subdivisions on the north and east sides of town. Our local technicians typically respond within 24 hours for non-emergency work, with same-day availability for most repair calls.
- Central Angleton and the historic downtown area
- North Angleton near Highway 35
- East Angleton around the Brazoria County Fairgrounds
- Subdivisions off FM 523 and Ranch House Road
- Areas near Angleton High School and the hospital
Service Area – Cities Near Angleton
Calder Gate Repair serves Angleton and the surrounding Brazoria County communities. If you’re in a nearby city, we’ve got you covered there too: Lake Jackson, TX, Clute, TX, Freeport, TX, and Alvin, TX. Scheduling and dispatch are coordinated from our Dallas-Fort Worth office, and local crews handle the Angleton area directly.
Serving Angleton, TX - Our Local Coverage Area
We’re based in the Angleton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Angleton
Most Angleton repair calls get same-day service. A live person answers the phone 24/7, and you’ll get a trackable arrival time rather than a four-hour window. Emergency calls for a gate that won’t close or secure typically move to the front of the schedule. Call (903) 417-0793 and we’ll tell you exactly when tech will be there.
For most repairs, no permit is needed. If your HOA has rules about gate style, color, or materials, we’ll work within those requirements on replacement parts and new installations. We can flag anything that might trigger HOA review before work starts so you’re never surprised after the fact.
We cover the entire city of Angleton, including the surrounding rural properties outside city limits. There’s no area of town we won’t service. If you’re unsure whether you’re in range, call (903) 417-0793 and we’ll confirm in about thirty seconds.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Angleton Customers Say
"Keypad and remotes reprogrammed in one visit. Paid by link."
- Pauline C."Good job on the motor. Part took a few days to arrive, but the updates came by text."
- Oscar J."Safety sensors realigned. Works fine. Photo eyes were dirty and out of line. Gate now stops when it should."
- Raul A.