Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Cedar Park
Most gate repairs in Cedar Park run $180 – $390 for common fixes like sag correction, opener board replacement, or safety sensor realignment, with parts priced separately and quoted before we touch a single bolt. If your gate is dragging on the driveway in Buttercup Creek or stuck mid-travel in Cypress Creek, call us at (903) 417-0793 and you’ll get a live person, not a voicemail. We service every subdivision across Cedar Park with background-checked techs who arrive in uniform with a trackable arrival time.
Why Calder Gate Repair Is Cedar Park’s Preferred Gate Repair Company
Calder Gate Repair is the dedicated Gate Repair specialist inside the Relay Home Co. family, and Cedar Park homeowners keep calling us back because we do three things every single time: we put the price in writing before work starts, we back every repair with a written 365-Day Done Right Promise, and we send a tech who tells you exactly when they’ll pull up. Not a four-hour window. A real arrival time you can track on your phone.
Our techs train across nine opener brands including LiftMaster, Linear, Viking, Ghost Controls, and DoorKing, so when a slide gate on a sloped Cedar Park driveway goes out of mesh, we diagnose it correctly the first visit. Nico Alvarez leads the team, and he’s built the Cedar Park service standard around one question: would we accept this repair at our own house? If the answer’s no, we redo it. That’s the 365-Day Done Right Promise, stated in writing on every job. If a repair fails within 365 days, we return free. No fine print, no phone tag.
Wrought Iron Gate Repair in Cedar Park
Wrought iron gate repair in Cedar Park almost always starts with the post, not the panel. The limestone-heavy soil under subdivisions like Ranch at Brushy Creek expands and contracts through wet-dry cycles, and that movement slowly heaves hinge posts out of level. A sagging iron gate is usually a post footing problem wearing a gate panel disguise.
Post Re-Set and Sag Correction
We pull the existing footing, re-set the post in concrete below the limestone active zone, and then re-hang the panel so it swings clean through its full arc. Skipping the footing and just re-hanging the panel is why so many Cedar Park gates sag again within a season. Typical post re-set work runs $220 – $380 depending on access and how much concrete the original builder actually poured.
Weld and Rust Repair
Cedar Park’s humidity and morning dew cycles keep surface rust active on older wrought iron. We grind back the affected sections, weld any cracked pickets or rails, and finish with a rust-inhibiting primer and paint match so the repair doesn’t stand out. Small weld-and-touch-up jobs run $120 – $250.
Metal Gate Repair in Cedar Park
Metal gate repair in Cedar Park covers everything from lightweight aluminum driveway gates to heavy steel slide gates on ranch-style properties off Whitestone Boulevard. The metal itself rarely fails first. What fails is what holds it: hinges, tracks, rack and pinion mesh, and the operator that drives it.
Slide Gate Track and Rack Correction
Sloped driveways in Cedar Park, especially through the hillier sections near Anderson Mill and Cypress Creek, put constant downhill pressure on slide gate racks. When the rack and pinion go out of mesh, the operator grinds, then strips the rack, then burns out the motor. We re-set the rack, shim the track, and adjust the limit switches so the gate stops where it’s supposed to. Rack re-mesh and track correction typically runs $190 – $310 before parts.
Safety Sensor and Edge Testing
UL 325 entrapment protection is not optional on automatic gates. Dust and pollen from Cedar Park’s greenbelt areas clog safety photocell lenses fast, and a dirty sensor means a gate that reverses for no reason or, worse, doesn’t reverse when it should. We clean, re-aim, and test every photocell and safety edge on every repair call. Sensor cleaning and re-aiming runs $95 – $160.
Trusted Brands We Service in Cedar Park
Our techs are factory-familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If your Cedar Park home has a Viking swing opener or a Linear slide operator, we know the board revision, the common failure points, and the correct replacement part without a guess-and-swap approach. We keep the most common boards, limit switches, remotes, and safety edge replacements stocked on our trucks so most repairs in Cedar Park don’t require a second trip.
Common Gate Repair Problems We See in Cedar Park Homes
- Sagging swing gates from post movement. Limestone soil expansion shifts hinge posts over time, especially in Buttercup Creek and Cypress Creek. The gate panel stays fine while the post leans out of plumb.
- Opener boards failing after temperature swings. Central Texas heat followed by overnight drops stresses LiftMaster and Linear control boards, leaving slide gates stuck mid-travel with no documented manual release.
- Photocell and safety edge failures from dust and pollen. Homes near the Cedar Park greenbelt see sensors clog fast. The UL 325 entrapment protection stops working silently, and most owners never notice until the gate misbehaves.
- Rack and pinion systems stripping on sloped driveways. Cedar Park’s hillier lots put gravity to work against slide gate racks, causing grind, strip, and eventually operator motor failure.
Pricing for Gate Repair in Cedar Park, TX
Here are the real ranges you can expect in Cedar Park before parts:
- Service call and diagnosis: $85 – $120
- Hinge post re-set: $220 – $380
- Sag correction on a wrought iron panel: $180 – $340
- Rack and pinion re-mesh: $190 – $310
- Safety sensor clean, re-aim, and test: $95 – $160
- Weld and rust touch-up: $120 – $250
- Full opener replacement (parts and labor, brand dependent): $650 – $1,400
Every price is quoted and agreed in writing before any work starts. The number on your invoice is the number we shook hands on at the door. Call (903) 417-0793 for a free estimate on anything above.
Keep in mind that full installations are measured, ordered, and scheduled. We don’t promise same-day installation, because a proper gate install includes groundworks, power run, safety edges, and reversal testing. What we promise is a free measure and a written price before anything gets ordered.
We Also Serve Cities Near Cedar Park
Calder Gate Repair covers all of Gate Repair in Cedar Park plus the surrounding communities: Leander, Round Rock, Pflugerville, and Georgetown. Dispatch is coordinated from the brand’s Austin office, and crews serve Cedar Park locally with trackable arrival times.
Serving Cedar Park, TX - Our Local Coverage Area
We’re based in the Cedar Park area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Cedar Park
Because the panel was never the problem. Cedar Park’s limestone-heavy soil expands and contracts with wet-dry cycles, and that movement heaves hinge posts out of level. If the post footing isn’t re-set below the limestone active zone, any panel re-hang is temporary. Post re-set work in Cedar Park runs $220 – $380 and fixes the root cause instead of the symptom. Call (903) 417-0793 and we’ll tell you within five minutes whether your sag is a post problem or a hinge problem.
Yes. UL 325 entrapment protection, meaning photocells and safety edges, is required on automatic gates anywhere in the U.S., including Cedar Park. A gate without working entrapment protection is a serious injury risk, which is why we test sensors on every repair and refuse to leave a gate operational if the safety system has been bypassed. Sensor clean and re-aim runs $95 – $160, and we carry replacements for all nine major brands.
Yes, we handle both daily. Swing gates are more common in established subdivisions like Buttercup Creek and Cypress Creek, while slide gates appear more on sloped lots and larger properties along Whitestone Boulevard. Both have distinct failure modes here: swing gates fight post movement, slide gates fight track and rack alignment. Either way, we diagnose first, quote in writing, and back it with the 365-Day Done Right Promise.
The short answer is yes, but we’ll be straight with you: solar works best on gates that cycle fewer than 10 times a day and get direct Central Texas sun. Cedar Park lots with heavy tree cover near the greenbelt often don’t get enough solar exposure to keep a battery bank healthy, so we’ll assess your actual sun hours before recommending a solar kit. A full solar opener installation in Cedar Park typically runs $900 – $1,600 depending on panel size, battery capacity, and gate weight. Free measure is included.
Most repairs, including hinge post re-sets, sag correction, rack re-mesh, and sensor replacement, are done in one visit of two to four hours. Full installations are different: they involve groundworks, power, safety edges, and reversal testing, so plan for one to three days depending on scope. We schedule installations in advance and never promise same-day install to rush a job that should be measured twice. Call (903) 417-0793 for a free estimate and an honest timeline for your specific gate.
If your gate is acting up in Cedar Park, don’t wait until it won’t open at all. One call to (903) 417-0793 gets you a live person, a free estimate, and a written price before any work begins.
Written by Nico Alvarez, Owner at Calder Gate Repair, serving Cedar Park through the Relay Home Co. family since 2009.