Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Madera
Gate repair in Madera usually comes down to one of three things: a hinge post that has shifted, an operator that was never set up right, or a safety sensor that got knocked out of alignment. Most repairs we handle in Madera run $180 – $340 before parts, and we can typically reach homes near Yosemite Avenue, the Ranchos, and the north-side subdivisions within a couple hours of your call. We are Calder Gate Repair, part of the Relay Home Co. family since 2009, and we show up with a written price before a single bolt gets turned. Call (903) 417-0793 and a live person answers, day or night.
Why Calder Gate Repair Is Madera’s Preferred Gate Repair Company
Madera gives us a particular mix of work that most gate companies never see. One call might be a 1920s iron swing gate near downtown that has sagged so badly it drags on the concrete. The next call could be a builder-grade slide gate in a newer subdivision off Avenue 12 where the operator was bolted to a post with no proper footing. We know both failure patterns because we have worked both sides of Madera for years.
Our technicians arrive in uniform, background-checked, with a live arrival time you can track from your phone. No four-hour windows. No voicemail tag. The Relay Standard means you get before-and-after photos of the work and a digital invoice you can pay from a link. When we finish a repair in Madera, you get the 365-Day Done Right Promise in writing: if the repair fails within a year, we come back at no charge. That is not a sales line. It is the guarantee Nico Alvarez, our lead technician, puts on every job we do.
Commercial Gate Repair in Madera
Commercial Gate Repair in Madera covers the automatic gates on apartments, storage yards, churches, and industrial lots from Madera Municipal Airport down to the warehouse rows along Highway 99. These gates fail differently than home gates: they cycle hundreds of times a day, so a limit switch that is slightly misadjusted becomes a full gate shutdown within a week. A limit switch, for anyone not deep in gate parts, is the small sensor that tells the gate when to stop at the open or closed position. When it drifts, the motor keeps pushing against the end stop and burns itself out.
Operator and Control Board Diagnosis
Commercial operators in Madera are most often FAAC, BFT, or Linear units, and we stock common control boards and limit switch kits for those brands locally. We test the full loop detector system, the safety photocells, and the reversing mechanism on every commercial call, because a gate that does not reverse when a car is under it is a liability you cannot afford.
Heavy-Duty Hinge and Post Work
Many commercial gates in Madera are heavy steel or ornamental iron mounted on posts set decades ago. When the post heaves from wet winters and hot summers, the gate binds against the latch and somebody forces it, which bends the frame. We re-square the posts, re-hang the gate, and re-mount the operator so the whole system works without a fight. Commercial work like this typically runs $250 – $600 depending on the gate size, with parts quoted separately and included in your written price before we start.
Iron Gate Repair in Madera
Iron Gate Repair in Madera is our most requested specialty, because Madera has a lot of ornamental iron gates, especially on the older homes near downtown and the ranch properties south and east of the city. Iron gates fail at the hinge post first. The post rusts at ground level or shifts in the soil, the gate sags, and then the latch stops lining up. Tightening the hinge bolts does not fix a post problem. We cut out and replace rotted post bases, re-concrete them, and re-hang the gate so it swings true.
Rust Treatment and Weld Repair
Madera’s summer heat bakes paint off iron gates, and the winter fog off the valley floor starts the rust. We grind out rust pockets, weld in new steel where the frame has rotted through, and re-prime and paint the repair to match. A weld repair on an iron gate in Madera typically starts around $95, and a full rust treatment and repaint of a standard 10-foot swing gate runs $350 – $700 depending on how much steel needs replacement.
Gate Realignment and Latch Repair
When a Madera iron gate still has solid posts but will not latch, the problem is usually the gate frame itself flexing or the latch plate worn down. We re-align the gate leaf, reinforce the frame where it has bowed, and install a fresh lock or latch so the gate actually closes and stays closed. This is the work that matters, because an iron gate that will not latch is just a decoration.
Trusted Brands We Service in Madera
Our techs are factory-familiar with the brands Madera homeowners actually have: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That means we carry the right replacement gears, control boards, remotes, and safety sensors on the truck instead of ordering them in and making you wait. FAAC and BFT show up a lot on the commercial side in Madera, while Viking and Linear are common on slide gates in the newer north-side subdivisions. If your opener brand is not on that list, call anyway. A gate is a gate, and a motor is a motor.
Common Gate Repair Problems We See in Madera Homes
- Sagging swing gates on older homes near Yosemite Avenue and downtown. The hinge posts were set in shallow concrete decades ago, and valley soil shifts with wet winters. The gate drops, the latch misses, and forcing it bends the hinges further.
- Slide gates that bind on newer north-side properties. Builder-grade installations often skip proper post footings or drainage, so the rack and pinion fight each other every cycle. The motor draws too much current and fails early.
- Disabled safety sensors after a DIY fix. We regularly find photocells bypassed or loop detectors unplugged because someone tried to fix a gate that would not close. An automatic gate without UL 325 entrapment protection is dangerous, and it is also a code violation.
- Worn rack and pinion gear sets on slide gates in the Ranchos. The long gravel driveways out there kick up dust that grinds the gears down. A new gear set is a fraction of the cost of a new operator, but if the post has shifted, you fix the post first or the new gear dies too.
Pricing for Gate Repair in Madera, CA
Most gate opener repairs in Madera run $180 – $340 before parts. The final number depends on what actually failed. A safety photocell replacement is typically $95 – $180. A limit switch replacement usually runs $130 – $220. A rack and pinion replacement on a slide gate typically runs $240 – $450 including parts. Full operator replacement on a standard residential slide or swing gate in Madera runs $700 – $1,500 for the unit and labor, depending on brand and gate size. We hand you a written price before any work starts. The number on the invoice matches the number you approved at the door, every time. No exceptions. Call (903) 417-0793 for a free estimate.
We Also Serve Cities Near Madera
Our crews cover Madera and the surrounding Central Valley communities. We handle Gate Repair calls in Fresno, Clovis, Kerman, and Chowchilla with the same written-price guarantee and the same 365-Day Done Right Promise. If you are in one of those cities and your gate refuses to open or will not shut, one call to (903) 417-0793 gets you on the schedule.
Serving Madera, CA - Our Local Coverage Area
We’re based in the Madera area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Madera
Because the hinge post itself has moved, and tightening the hinge bolts only pulls the gate closer to a post that is no longer vertical. Madera’s clay-heavy soil expands and contracts with the wet winters and dry summers, and older posts set in shallow concrete eventually heave or lean. The fix is to excavate the post, re-set it plumb in new concrete, and re-hang the gate. That is a job we do regularly around the older neighborhoods near Yosemite Avenue. Call (903) 417-0793 and we will check the post before anyone quotes you a hinge replacement.
No, and you should be careful of anyone who says it is. A proper gate installation in Madera involves post holes dug to the right depth, concrete that needs to cure, power run correctly for the operator, and safety sensors that have to be tested. That work takes measured time. We schedule installations with a firm date and a clear scope, give you a written price upfront, and keep you updated with a live arrival time on the day. Repairs can often happen same-day; a new gate is scheduled and done correctly the first time.
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, which covers nearly every operator a Madera homeowner is likely to own. We stock common parts for these brands locally, so a FAAC control board swap or a Linear limit switch job usually does not mean waiting on a shipment.
Yes, every automatic gate in Madera needs functioning entrapment protection, which means safety photocells and loop detectors that meet UL 325 standards. If those sensors are misaligned, bypassed, or disconnected, the gate can close on a car, a child, or a pet. We test reversing force and sensor alignment on every automatic gate we touch, and we will not hand a gate back to you with the safety system disabled.
Most gate opener repairs in Madera run $180 – $340 before parts, with common fixes like photocell replacement at $95 – $180 and limit switch work at $130 – $220. Full operator replacements generally land between $700 and $1,500. You get an exact written price before we start, so there is no guessing. Call (903) 417-0793 for a free estimate specific to your gate.
We cover all of Madera, including the Madera Ranchos, the neighborhoods off Avenue 12 and Avenue 17, the downtown blocks around Yosemite Avenue, and the country properties south of town. Our dispatch and scheduling are coordinated from the Fresno, Central Valley office, with crews serving Madera locally. We will give you a live arrival time you can track, not a vague window.
If your gate is stuck, sagging, beeping, or simply refusing to open, call Calder Gate Repair at (903) 417-0793. A live person answers. You will get a written price before any work starts, a real arrival time, and a repair backed by the 365-Day Done Right Promise.
Written by Nico Alvarez, Owner at Calder Gate Repair, serving Madera and the Central Valley since 2009.