Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Hornsby Bend, TX
Gate repair in Hornsby Bend means working with the Colorado River bottomland: shifting clay soil, fast-growing vegetation, and a mix of 1970s-90s ranch-style homes on larger lots alongside newer builds east of 183. Most Hornsby Bend gates are driveway swing gates or slide gates on tracked wheels, and the soil movement here is a real factor, not a talking point. Calder Gate Repair handles everything from a dead opener to a gate that’s dragging on its hinges, with a written price before any work starts. Call (903) 417-0793 and a live person answers.
Why Hornsby Bend Homes Are Different
Hornsby Bend sits on the east side of the Colorado River, and the soil is the defining character here. Expansive clay swells after rain and shrinks during dry spells, which means gate posts move. A gate that swung cleanly in April can catch the latch plate by August. We see this constantly in Hornsby Bend: posts that have heaved half an inch, throwing the gate out of level and burning out opener motors that have to work against the bind.
Mature live oaks and pecan trees are everywhere in the older river-bend lots, and root growth under gate tracks and operator pads is a leading cause of slide-gate failure. Hornsby Bend also has stretches of rural long-driveway properties where a gate can sit 300 feet from the house, which makes a wired intercom or a wireless keypad rely on a clean power run and a well-adjusted antenna. Newer subdivisions on the west side of FM 969 tend toward tighter lots with ornamental steel gates and HOA rules about gate appearance and noise. Working in Hornsby Bend means knowing which job is a soil problem, which is a vegetation problem, and which is just a tired motor.
Our Main Hornsby Bend Services
Most calls from Hornsby Bend homeowners fall into one of three buckets: the gate itself won’t move, the electric system isn’t powering it, or the opener is running but not doing its job. Each has its own dedicated Hornsby Bend page below.
Gate Repair in Hornsby Bend
When a gate drags, sags, or won’t latch in Hornsby Bend, it’s usually the hinges, the post alignment, or the track. Our crews are familiar with the clay-soil post movement common along the Colorado River corridor and check for ground shift as part of every diagnosis. A gate that’s out of level is often the root cause behind a string of opener failures. We quote the hinge, wheel, track, or weld repair in writing before touching a bolt. Gate Repair in Hornsby Bend covers the full rundown.
Electric Gate Repair in Hornsby Bend
Hornsby Bend’s mix of older rural wiring and newer low-voltage runs means electric gate faults here are rarely one-size-fits-all. We trace openers, keypads, safety loops, and photocells, and we’re used to finding corroded splices from past flood-plain moisture. If a gate works from one button but not another, the fix could be a card reader in the driveway or a transformer in the control box. The written diagnosis is part of the upfront price. See Electric Gate Repair in Hornsby Bend for specifics.
Gate Opener Repair in Hornsby Bend
Openers in Hornsby Bend take a beating from heat, dust, and the occasional armadillo digging under a safety loop. A common failure we see is the limit switch – the small sensor that tells the gate when to stop – wearing out and letting the opener overrun. We service openers from LiftMaster, FAAC, BFT, and six other major brands, and we’ll tell you honestly whether a replacement board beats a new motor. Full details on Gate Opener Repair in Hornsby Bend.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Hornsby Bend
We’re factory-familiar with nine major opener brands, and the ones Hornsby Bend homeowners own most are Linear, Viking, Ghost Controls, and DoorKing. Common boards, remotes, and limit switches for these are stocked on our trucks, which usually means one trip instead of two. See our brands for the full list.
Pricing for Gate Company in Hornsby Bend, TX
These are the numbers we quote most often in Hornsby Bend. Every job gets a written price before work begins, so the figure below is what you can expect to see, not a teaser.
| Service | Typical range in Hornsby Bend |
|---|---|
| Gate opener repair | $180 – $340 before parts |
| Electric gate repair | $200 – $450 before parts |
| Gate repair (hinges, wheels, alignment) | $150 – $400 before parts |
| Gate safety sensor replacement | $120 – $250 |
| Gate remote/receiver programming | $75 – $150 |
| Gate track repair or replacement | $200 – $500 |
| Gate opener installation | $450 – $900 plus opener |
| Full gate opener replacement | $700 – $1,500 with labor |
What pushes a Hornsby Bend gate repair toward the top of a range is usually access: a long river-bottom driveway with a single-track path, a post that needs re-setting in clay soil, or a corroded splice that requires re-pulling wire. You’ll hear the number before we start, and that number does not change at the door.
Neighborhoods We Serve in Hornsby Bend
We run crews through every part of Hornsby Bend, from the older river-bend lots west of FM 969 to the newer subdivisions going in along the Colorado’s east bank. Typical response time across the area is same-day for most repair calls, depending on when you reach us.
- Hornsby Bend east of 183 along FM 969
- River-bend acreage west of the Colorado
- Subdivisions off Harold Green Road
- Streets near Hornsby-Dunlap Elementary
- Long-driveway properties along Dunlap Road
Service Area – Cities Near Hornsby Bend
If you’re just outside Hornsby Bend, our scheduling covers the surrounding metro. We run calls into Houston, TX, handle work in San Antonio, FL, and serve Dallas, TX and Fort Worth, TX through the same Relay Visibility Guarantee. Dispatch is coordinated from the brand’s Austin office, and crews serve Hornsby Bend locally.
Serving Hornsby Bend, TX - Our Local Coverage Area
We’re based in the Hornsby Bend area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Hornsby Bend
Most Hornsby Bend repair calls are handled same-day, and a live person answers the phone 24/7 to book or update you. We dispatch with a live, trackable arrival time, not a four-hour window. If it’s a safety issue, tell the dispatcher and we’ll prioritize it. Call (903) 417-0793 for a free estimate.
Some of the newer subdivisions in Hornsby Bend have HOA rules about gate style, height, and color, especially on ornamental steel. We can help you determine what your community requires before we quote, so there are no surprises. The county permitting for gate work is minimal, but we’ll flag anything that needs sign-off.
Yes. Our scheduling covers weekends and evenings, which matters when a gate fails on a Friday and your driveway is the only way in. A live person books the appointment 24/7, and you get a written price before any work starts. Call (903) 417-0793 and we’ll get you on the board.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Hornsby Bend Customers Say
"Keypad and remotes reprogrammed in one visit. Paid by link."
- Pauline C."Good job on the motor. Part took a few days to arrive, but the updates came by text."
- Oscar J."Safety sensors realigned. Works fine. Photo eyes were dirty and out of line. Gate now stops when it should."
- Raul A.