Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Farmers Branch
Gate repair in Farmers Branch usually comes down to three things: a post that shifted in the clay, an opener that overheated and failed, or a safety sensor that never got re-tested after install. Most jobs run $180 – $520 depending on what actually failed, and we quote that price in writing before any work starts. If your swing gate drags, your slide gate stalls mid-travel, or your opener just clicks and does nothing, call (903) 417-0793 and a live person answers, 24/7.
We’re Calder Gate Repair, the dedicated gate division inside the Relay Home Co. family, and our Gate Repair technicians work across Farmers Branch every week, from the older ranch-style lots near Valwood Park to the newer builds east of Webb Chapel Road. You won’t get a four-hour window. You’ll get a background-checked, uniformed tech with a live arrival time you can track, a written price before we touch a bolt, and a real 365-Day Done Right Promise behind the work.
Why Calder Gate Repair Is Farmers Branch’s Preferred Gate Repair Company
People in Farmers Branch call us because gate work here has a very local failure pattern. The Blackland Prairie clay under your posts absorbs water in spring, shrinks in August, and the posts move. Not much, maybe half an inch at the base, but that’s enough to drag a swing gate, bind a slide track, or strip the gear on a perfectly good opener. We plan for that soil on every job, not just the ones where the post is visibly leaning.
Every Farmers Branch job runs under what we call the Relay Standard: a trackable arrival time, before-and-after photos, and a digital invoice you can pay from your phone. The price on that invoice matches the number we agreed to at the door, every time. And every repair carries our 365-Day Done Right Promise, which means if the same problem comes back within a year, we return and fix it at no charge. Written on the job. Not optional.
Nico Alvarez, who runs our repair program, trains every tech on nine major opener brands including LiftMaster, DoorKing, and Ghost Controls. That matters here because Farmers Branch has a wide mix of stock LiftMaster operators on older gates and aftermarket upgrades on newer ones, and misdiagnosing an opener board when the real problem is a shifted post wastes your money. We don’t guess. We test, we measure, and we explain what actually failed in plain words.
Dispatch for Farmers Branch is coordinated from our DFW office, and crews run local routes through the city daily. Response is typically same-day for emergency gate failures, and you’ll always reach a human on the phone, not a voicemail tree.
Metal Gate Repair in Farmers Branch
Metal Gate Repair in Farmers Branch most often starts with the ground, not the iron. A steel or aluminum gate is only as straight as the posts holding it, and with our expansive clay soils, hinge posts tilt over two or three wet-dry cycles even when the concrete was set correctly at the start. That tilt puts the whole panel in a bind, wears hinge bushings fast, and makes the opener work against itself.
When we repair a metal gate, we check the plumb of both posts with a laser level before anything else. If the post has shifted, we’ll dig out the footing, re-pour it with a deeper base and better drainage, and then address the panel itself: hinge replacement, weld repair, sag correction, or a full re-hang. A basic hinge and alignment job in Farmers Branch typically runs $180 – $320. If we’re pulling and re-setting a post, count on $350 – $520 depending on the footing and whether we need to core out old concrete.
Hinge, Post, and Realignment Work
When a metal gate drags along its latch post but the panel sections look straight, the fix is almost always in the hinge post. We remove the gate from its hinges, re-set and brace the post while the footing cures, then re-hang the panel and adjust the gaps so it swings without binding. Worn hinge bushings get replaced at the same time, not patched with grease.
Most realignment and hinge work on Farmers Branch steel gates is finished same-day, because the concrete we use sets fast and the re-hang doesn’t take long once the post is in.
Weld and Rust Repair
Farmers Branch’s hot, humid summers and the occasional ice storm put real stress on welded joints. Hairline cracks at the hinge plate or mid-rail aren’t cosmetic. They’re the start of a panel that folds under its own weight. We grind out the cracked weld, re-weld with proper penetration, and re-coat the area so rust doesn’t take root. Rusted-through rails get sectioned and replaced rather than patched, because a patch on a load-bearing rail fails again within a season.
Weld repair jobs in Farmers Branch usually add $120 – $200 to the base repair, depending on how many joints need to be re-done.
Wood Gate Repair in Farmers Branch
Wood Gate Repair in Farmers Branch is a different animal than in most Texas cities because the same clay that shifts posts also holds water against the bottom rail longer, accelerating rot at precisely the joint where the panel carries the most weight. A wood gate in this city often looks fine from the street and is rotten through at the lower hinge mount.
We start by grading the panel and frame: is the wood sound enough to save, or has the bottom rail turned soft? For salvageable gates, we sister new framing, replace hinge lag bolts with through-bolts, correct the sag with a proper turnbuckle and cable setup or a rebuilt frame, and re-align the latch. Typical Farmers Branch wood gate repair runs $200 – $400 depending on how much framing we replace and whether the post needs work too.
Sag Correction and Frame Rebuilds
Wood gates sag when the diagonal brace is installed wrong or when bottom rail rot lets the outer stile drop. We cut new pressure-treated rails, re-square the frame on a flat surface, and secure the corners with structural screws rather than drywall screws that rust and snap. Every rebuild includes the diagonal brace run the correct direction, from the bottom hinge up toward the latch, because a backwards brace does nothing to fight gravity.
Post Reset and Latch Replacement
If your wood gate post wobbles when you push on it, the concrete core is likely cracked below the soil line. We remove the rotten or tilted post, set a new pressure-treated post in a deeper footing with gravel drainage at the base, and re-mount the gate. Old latch hardware usually gets replaced at the same time, since a misaligned latch is what forces the post sideways in the first place. Count on $320 – $500 for a full post reset with latch replacement in Farmers Branch.
Trusted Brands We Service in Farmers Branch
Our Farmers Branch trucks carry common parts for Linear, Viking, Ghost Controls, and DoorKing operators, plus a full range of LiftMaster boards and gear kits. That local parts stock means a slide gate operator that died from a bad capacitor can often be running again the same day, without waiting on a part that ships from out of state. We’re factory-familiar with all nine major residential brands, so we don’t show up with a generic board and hope it fits. We carry or source the exact part for your specific opener, and we verify compatibility before quoting you the repair.
Common Gate Repair Problems We See in Farmers Branch Homes
- Clay-shifted hinge posts on swing gates. Farmers Branch sits on Blackland Prairie clay that swells after rain and shrinks in drought. A post set five years ago can be out of plumb by an inch today, and that’s what’s dragging the gate, not the panel itself.
- Opener boards and battery backups killed by summer heat. Dallas-area heat inside a metal control box pushes circuit boards past their design limits. We see slide gates stall mid-travel or refuse to close entirely because the board cooked while the battery backup silently failed.
- Photo-eyes and safety edges that were never re-tested. Installers often mount the sensors, confirm the gate opens and closes once, and leave. The first time the gate reverses or bumps a car, the misalignment becomes obvious. We re-test entrapment protection on every job. It’s part of the written checkoff.
- Slide gates binding on a track that’s moved with the ground. Long concrete track runs in Farmers Branch can crack or settle unevenly as the soil moves, and a quarter-inch deviation at the track mid-span will make the opener draw more amps and eventually trip its thermal protection.
Pricing for Gate Repair in Farmers Branch, TX
Most gate repairs in Farmers Branch, TX fall into predictable ranges. Hinge and alignment work runs $180 – $320. Pulling and resetting a shifted post adds $150 – $250 to the job. Opener board replacements typically land between $200 – $450 depending on the brand and whether the battery backup is also dead. Full weld and rust repair adds $120 – $200. A complete wood gate frame rebuild, including post reset, runs $320 – $500. These are the numbers before tax, and every one of them goes in writing before any work starts. The invoice you get at the end matches the quote from the start. Call (903) 417-0793 for a free estimate on your specific gate, and we’ll tell you exactly what we found and what it costs.
We Also Serve Cities Near Farmers Branch
While this page covers gate work in Farmers Branch, our crews also run routes into Dallas, Fort Worth, and the surrounding metro. If you’re outside the city but still need Gate Repair in Farmers Branch level service, call and we’ll coordinate the nearest available tech. We serve Houston and San Antonio through the wider Relay Home Co. network as well.
Serving Farmers Branch, TX - Our Local Coverage Area
We’re based in the Farmers Branch area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Farmers Branch
Because the post, not the gate panel, is the problem. The expansive Blackland Prairie clay under your hinge post swells and shrinks, and every wet-dry cycle moves it a little more. A repair that only adjusts the panel won’t hold because the foundation keeps shifting. A real fix means resetting the post in a deeper footing with drainage gravel, and that’s what we do when we see the pattern.
A proper installation includes the boring parts nobody wants to think about: a post footing below the clay layer so the Soil doesn’t push it out of plumb, the power run from the panel to the operator, safety edges and photo-eyes that are tested for entrapment reversal, and a travel limit setup that doesn’t slam the gate at either end. In Farmers Branch, the footing depth matters more than anywhere because the Blackland clay moves so much. If you’re planning an install, call (903) 417-0793 for a free measure and a written price. We don’t rush installations, and we don’t cut the footing depth to hit a deadline.
Yes. Automatic gates must have working entrapment protection: photo-eyes, safety edges, or both, depending on the configuration. The sensors must reverse the gate if a person or car is in the path. We re-test that reversal on every repair and every install. If your current gate doesn’t reverse properly, that’s not a future project. It’s a safety issue now.
Usually yes. A clicking board, a bad capacitor, a stripped gear, or a failed limit switch is repairable, especially on LiftMaster and DoorKing openers where parts are readily available. We only recommend replacement when the board shows burn marks, the motor windings are shorted, or the failure is cascading. Repair runs $200 – $450 in most Farmers Branch cases; we’ll show you the failed part and explain the repair before you pay. Call (903) 417-0793 and we’ll diagnose it on site.
Most repairs finish in 2 – 4 hours. Hinge, alignment, opener board, and safety sensor work are often same-day. Installations are not: a proper new gate or opener install in Farmers Branch involves a measure, a written quote, footing work with cure time, and scheduled install. We don’t promise same-day installation because we won’t cut the steps that make it last. Emergency repair calls get priority response.
If your gate is dragging, stalling, or refusing to close, stop guessing at the cause and call (903) 417-0793. A live person answers, we’ll book a tracked arrival time, and you’ll get the written price before any work starts. That’s the Relay Standard, and it’s how we work in Farmers Branch, TX, every day.
Written by Nico Alvarez, Owner at Calder Gate Repair, serving Farmers Branch and the Dallas-Fort Worth metro.