Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Inglewood
Gate repair in Inglewood usually comes down to one of two things: a footing that has shifted in the local clay, or an operator that has lost its calibration. Most driveway gate repairs here run $180 – $340 before parts, and we can typically have a technician at your door the same day you call. Calder Gate Repair is the dedicated gate specialist inside the Relay Home Co. family, and our crews know Inglewood’s streets, soil, and housing stock better than any regional outfit ever could. If your gate is sagging, stuck, or refusing to close, call us at (903) 417-0793 and a live person will answer. No voicemail, no callback roulette.
Why Calder Gate Repair Is Inglewood’s Preferred Gate Repair Company
We back every job in Inglewood with the 365-Day Done Right Promise. Written down, every time. If a repair fails within a year, Calder returns at no charge and makes it right. That is not a slogan. It is the same guarantee we have put in writing since 2009, and it applies to every hinge, weld, motor, and keypad we touch.
Our technicians arrive in uniform, background-checked, with a live arrival time you can track from your phone. The Relay Standard, which we follow on every Inglewood job, means you get before-and-after photos and a digital invoice you can pay from a link. The price we quote at the door is the price on the invoice. Written before any work starts, never a surprise at the end.
Nico Alvarez leads Calder Gate Repair, and he built the Inglewood team around a simple idea: gate repair should feel like booking a rideshare, not scheduling a cable company. You know who is coming, when they will arrive, and what it will cost. We dispatch from our Los Angeles office and crews serve Inglewood locally, which keeps response times short and local knowledge deep.
Our Gate Repair team is factory-familiar with nine major opener brands, so when a Viking or BFT unit acts up near Morningside Park, we are not guessing from a generic manual. We know the wiring, the failure points, and the fix.
Driveway Gate Repair in Inglewood
Driveway Gate Repair in Inglewood is the service we get called for most often, and it usually starts with a gate that worked fine for years and then started sagging, grinding, or stopping mid-travel. The panel is rarely the problem. What we find is a hinge post that has loosened in the expansive clay around the La Cienega – Centinela corridor, or a slide gate that has drifted off its track because the post footing under the rack shifted. Inglewood sits on the older Inglewood fault zone of the Newport – Inglewood Fault System, and post footings here move seasonally. That swell-shrink cycling is why so many Inglewood swing and slide gate failures trace back to the hinge post or post footing rather than the gate panel itself.
Typical driveway gate repair in Inglewood runs $180 – $340 before parts, with most jobs completed in a single visit. If the footing is cracked and needs to be reset, expect the price to land at the upper end of that range because the post has to be pulled, re-leveled, and re-anchored.
Hinge & Post Reset
A sagging wooden gate off 90th Street or near Morningside Park is almost always a post problem, not a panel problem. We remove the gate, reset the post in fresh concrete, and re-hang the panel so it clears the ground evenly. This stops the sag from coming back in six months.
Gate Realignment
Slide gates in Inglewood drift when the clay under the track heaves after winter rain. We re-level the rack, re-shim the track, and re-tune the operator limits so the gate opens and closes without binding.
Gate Welding in Inglewood
Gate Welding in Inglewood is the fix when a wrought-iron gate has cracked at a hinge mount, a post has rusted through at the base, or a welded seam has separated after years of cycling across Century Boulevard traffic. We repair the steel in place whenever possible, grind the joint clean, and weld it using the same-gauge material as the original frame. Inglewood’s older 1920s-era bungalows often have original wrought-iron driveway gates, and those pieces are worth repairing rather than replacing. A cracked gate panel is not a lost cause.
Most gate welding repairs in Inglewood run $220 – $450 depending on the length of the crack and whether the gate needs to be removed for work on both sides. We quote the full price before we strike an arc.
Weld & Rust Repair
Rust at the bottom rail is the most common weld point we see on Inglewood gates, especially near the coast where marine air pushes inland. We cut out the rotted section, weld in new steel, and coat the repair so it does not fail at the same seam next year.
Post Replacement Welding
When a hinge post snaps at ground level, we weld a new post stub to the existing footing anchor or install a fresh post with a welded hinge plate. The gate goes back on straight, and the welds get a rust-inhibiting treatment before we leave.
Trusted Brands We Service in Inglewood
Our Inglewood technicians work on FAAC, BFT, Linear, and Viking openers regularly, plus the rest of the nine major brands we support across the Relay Home Co. network. That matters because a FAAC hydraulic unit and a Viking electromechanical unit fail differently, and the fix is not interchangeable. For Inglewood customers, our familiarity with these systems means we can often source the right limit switch, control board, or capacitor the same day instead of ordering blind. When a Linear keypad goes dead near Holly Park Knolls, we know the wiring sequence and the reset procedure without fumbling through a phone tree.
Common Gate Repair Problems We See in Inglewood Homes
- Post footings loosening from expansive clay. Inglewood’s soil swells when wet and shrinks when dry, and over two or three seasons that cycle works a hinge post loose. The gate sags, drags, or refuses to latch even though the panel itself is straight.
- Operators tripping because the safety photocell is misaligned. A LiftMaster or BFT operator will stop and reverse mid-cycle if the photo eye or loop detector is blocked or knocked out of alignment. The motor is usually fine. The sensor is not.
- Keypad and manual-override failures on older gates. We see this on Inglewood gates where the operator was replaced years ago but the original low-voltage wiring was never re-checked against the new unit. The keypad works intermittently, or the manual release jams because the old chain and new sprocket were mismatched.
- Welds cracking at the hinge mount. Wrought-iron gates from Inglewood’s 1920s-era bungalows were built with thick steel and good intentions, but decades of swinging in coastal air weakens the welds at the hinge side. A cracked weld makes the gate lean and puts load on the operator it was never meant to carry.
Pricing for Gate Repair in Inglewood, CA
Here are honest numbers for Inglewood, not vague ranges that balloon after the tech arrives. Basic gate realignment and hinge tightening runs $150 – $250. Driveway gate repair with a post reset lands between $180 – $340 before parts. Gate welding starts around $220 and goes to $450 for larger cracks or post replacement work. Operator repair and limit switch replacement runs $190 – $320, depending on the brand and whether we need a control board. Every job gets a written price before any work starts. That is our rule, not an upsell. Call (903) 417-0793 for a free estimate, and the number we give you is the number you pay.
We Also Serve Cities Near Inglewood
Calder Gate Repair covers the neighborhoods around Inglewood too. If you are in Hawthorne, Culver City, El Segundo, or Lawndale, the same written-price guarantee and 365-Day Done Right Promise apply. For the full picture on how we serve the wider area, see Gate Repair in Inglewood and surrounding communities.
Serving Inglewood, CA - Our Local Coverage Area
We’re based in the Inglewood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Inglewood
Usually not. The most common cause in Inglewood is a misaligned safety photocell or a blocked photo eye, which tells the operator to stop and reverse for safety. The motor is often fine, and the fix is a realignment, not a replacement. We check the sensor, the loop detector, and the limit switches before we ever quote a new motor. Call (903) 417-0793 if your gate will not close, and we will tell you over the phone whether it sounds like a sensor issue or something bigger.
Most hinge, realignment, and operator calibration jobs in Inglewood are done in one visit, usually 1.5 to 3 hours depending on whether a post needs to be reset. Welding jobs and full post replacements can take a half day, and we will tell you the timeline before you approve the work. If a part has to be ordered for a specific operator brand, we will give you a real lead time, not an open-ended “soon.”
Because the problem is the post footing, not the panel. Inglewood’s expansive clay and the Newport – Inglewood Fault System run right under the city, and post footings here shift seasonally as the soil swells and shrinks. Fixing the panel without resetting the post is like painting over a crack in the foundation. We reset the post in fresh concrete and re-hang the gate so it stays level through wet winters and dry summers.
Yes. We service solar gate openers and keypad entry systems across Inglewood, including the older wired setups on pre-1980 bungalows where the original wiring was never upgraded when the operator was replaced. We check the low-voltage run, the manual release, and the keypad programming against the current unit. If the keypad is dead, we can usually restore it or install a compatible replacement the same visit. Call (903) 417-0793 for a free estimate.
A real gate installation quote in Inglewood should include groundworks, power run, safety edges, and full reversal testing. Cheap quotes skip the safety photoelectric edges or the reversal force test, and that is exactly what puts a gate out of code and creates a crushing hazard. We never offer same-day installation because proper groundworks and safety edge installation take measured, scheduled work. We will give you a line-item written price that shows every part of the job, so you can compare honestly. Call (903) 417-0793 for a quote that covers the whole installation, not just the gate panel.
Written by Nico Alvarez, Owner at Calder Gate Repair, serving Inglewood and surrounding communities since 2009.