Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Richland Hills
Gate repair in Richland Hills usually comes down to three things: a post that shifted in the clay, an operator that lost its safety sensors, or a hinge that gave up after years of Texas heat. Most repairs run $180 – $500, and we can typically get a tech to your Richland Hills driveway the same day you call. Calder Gate Repair is the dedicated gate specialist inside the Relay Home Co. family, and our crews know Richland Hills lots well: tight front yards, gates that swing within feet of the sidewalk, and soil that moves more than homeowners expect. Call (903) 417-0793 and a live person will answer, 24/7.
That last part matters. You won’t get a voicemail or a chatbot when your gate is stuck open at 8pm. You’ll get a person who can book a tech, look up your address, and confirm the price range before you hang up. That’s how we work across Richland Hills.
Why Calder Gate Repair Is Richland Hills’s Preferred Gate Repair Company
We’ve done enough Gate Repair work in Richland Hills to know the difference between a Dallas gate and a Richland Hills gate. The lots are tighter here. Houses along Baker Boulevard, Rufe Snow Drive, and the neighborhoods off Glenview Drive tend to have gates that swing over public sidewalk or right up against the driveway apron. That changes how a gate gets built, welded, and tested. It also changes which failure modes show up first.
Our techs arrive in uniform, background-checked, with a live arrival time you can track from your phone – not a four-hour window. Every job starts with a written price before any work begins. The number you agree to at the door is the number on the invoice. That’s the Relay Standard, and it applies to every Richland Hills home we serve.
Nico Alvarez, who leads Calder Gate Repair, set the rule early: we name the brand we’re fixing, we explain the part in plain English, and we stand behind the repair for a full year. The 365-Day Done Right Promise means if the repair fails within 365 days, Calder returns at no charge. Free second visit. Written guarantee. No fine print gymnastics.
Gate Welding in Richland Hills
Gate welding in Richland Hills usually starts with a question: is the metal actually broken, or is the post moving underneath it? On a corner lot off Baker Boulevard, our tech found a steel swing gate drooping into the curb because the hinge post footing had shifted in the clay. The gate panel itself was straight. The homeowner blamed the LiftMaster operator, but the real fix was resetting the post footing and doing sag correction before we touched the gate operator. Once the post was solid and the panel swung true, the gate passed its safety photocell and reversal test on the first attempt. That’s the order we follow: post first, panel second, operator third.
Typical gate welding in Richland Hills runs $150 – $400 for a cracked hinge, broken weld joint, or a sagging corner that needs reinforcement. If the post is the actual problem, expect $350 – $800 to reset the footing in fresh concrete, depending on how deep the clay has shifted.
Cracked Hinge and Latch Repairs
Most cracked hinges happen because the gate panel flexes against a post that’s no longer plumb. We weld the crack, gusset the weak point, and reset the panel so the stress doesn’t just move to the next weld. We grind, prep, and weld with proper penetration, not a quick tack.
Post Footing Resets in Clay Soil
North Texas clay expands when wet and shrinks when dry. Over a few seasons, that cycle can push a hinge post out of vertical. If your gate scrapes the driveway but the panel looks straight, the footing is the likely culprit. We dig it out, re-pour with proper depth, and set the post dead plumb before re-hanging the gate on fresh hinges.
Commercial Gate Repair in Richland Hills
Commercial gate repair in Richland Hills isn’t just residential work on a bigger panel. The gate duty cycle is higher, the operator is usually mid-grade or heavy-duty (FAAC, BFT, or Linear), and the safety requirements are less forgiving. A slide gate that drags its rack and pinion against a bent track near the driveway apron will chew through a gearbox in months if the track isn’t straightened first. We see that a lot on commercial lots along the Grapevine Highway corridor.
Commercial gate repair in Richland Hills typically runs $350 – $1,200 depending on whether we’re replacing a gearbox, fixing rack alignment, or doing a full operator swap. It’s measured, quoted, and scheduled, not a same-day scramble. You get a written price before any parts are ordered, and a free measure if you want the gate evaluated before committing.
Slide Gate Rack and Pinion Service
When the rack is bent or the pinion gear is worn, the gate jerks instead of sliding smooth. We straighten or replace the rack section, set the gear mesh correctly, and test the gate under load. On most Richland Hills commercial sites, this is a same-visit fix unless the track itself needs re-anchoring into the slab.
Operator Replacement for Commercial Gates
When a FAAC or BFT operator is beyond a repair, we spec the correct replacement based on gate weight, panel length, and daily cycle count. Then we handle the wiring, the safety loop replacement, and the UL 325 entrapment testing so the gate is compliant before you open the lot back up. Installations are scheduled, quoted, and never rushed.
Trusted Brands We Service in Richland Hills
Our techs are factory-familiar with nine major gate opener brands, and in Richland Hills we see a lot of LiftMaster on swing gates, FAAC and BFT on commercial slide gates, and Linear on older residential operators. We keep common boards, remotes, limit switches, and safety edge parts in local stock, so many Richland Hills repairs don’t wait on a parts shipment. If your gate is from Viking or Gate Operator Pro, or something less common, we can usually source it within a day or two. Tell us the brand when you call, and we’ll tell you honestly if it’s a part we can replace same week.
Common Gate Repair Problems We See in Richland Hills Homes
- Hinge post footings moving in clay. Richland Hills sits on expansive clay that shifts with every wet-dry cycle. When the post leans, the gate drags at the latch even though the panel is straight, and the fix is a footing reset, not a panel weld.
- Safety photocell and edge misalignment on tight-lot swing gates. Gates that swing within a few feet of the sidewalk can fail their UL 325 entrapment test if the photo-eyes get knocked out of alignment. A gate that doesn’t reverse when a kid is in the path is a street-side hazard, not just an annoyance.
- Slide gate rack and pinion wear near the driveway apron. Bent track sections near the slab eat pinion gears. The gate jerks, then stops, and the homeowner assumes the operator died when it’s actually a mechanical rail issue.
- Dead loop detectors and keypad entry failures. Often paired with a working gate that just won’t open on approach. We test the loop first, then the keypad, and only replace the operator if the electronics are actually fried.
Pricing for Gate Repair in Richland Hills, TX
Most gate opener repairs in Richland Hills run $180 – $400 before parts. Hinge and latch welding falls between $150 and $400. A full post footing reset runs $350 – $800. Commercial operator replacements land in the $350 – $1,200 range depending on panel weight and operator class. New installs are priced per project, not from a menu, and you’ll get a written estimate after we measure. Every repair includes the 365-Day Done Right Promise: if it fails within a year, Calder returns free. Call (903) 417-0793 for an exact quote on your gate – estimates are free, and the price you approve is the price you pay.
We Also Serve Cities Near Richland Hills
Calder Gate Repair handles Gate Repair in Richland Hills plus the surrounding metro. We regularly dispatch to Houston, San Antonio, Dallas, and Fort Worth for larger commercial jobs and scheduled installations. If you’re outside Richland Hills but still in the region, call us and we’ll confirm coverage.
Serving Richland Hills, TX - Our Local Coverage Area
We’re based in the Richland Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Richland Hills
Sometimes, yes – but not if the hinge post has moved. We’ll check the post with a level before touching the panel. If the footing is solid, a sag correction plus local welding usually fixes the scrape for $150 – $400. If the post has shifted in the clay, welding won’t last and you’ll pay for the repair twice. We’ll reset the post, re-hang the gate, and then weld any hinge damage that formed along the way. Call (903) 417-0793 and we’ll assess it on site.
Yes. UL 325 requires entrapment protection on automatic gates, and that means functioning photo-eyes or an equivalent safety edge. On Richland Hills lots where swing gates close within a few feet of the sidewalk, misaligned photo-eyes are a street-side risk: a gate that doesn’t reverse on contact can hurt a pedestrian. We test photo-eye alignment and reversal force on every automatic gate repair, and we won’t leave a gate energized if it fails. It’s a safety requirement, not an upsell.
We repair LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The most common operators we see in Richland Hills are LiftMaster on residential swing gates, FAAC and BFT on commercial properties, and Linear on older slide systems. We stock common boards and safety parts locally, so most repairs don’t wait on shipping.
A typical repair – hinge, sensor alignment, board swap, rack adjustment – is done same visit, usually in 1 – 3 hours. A new gate installation is different: that’s measured, quoted, scheduled, and built, with groundwork, power run, safety edges, and reversal testing. Installation takes days, not hours. We never promise same-day turnaround on a new gate. For repair speed, call us and we’ll confirm a live arrival time.
Yes. Bent rack sections near the driveway slab are a common Richland Hills failure, especially where the ground has settled. We straighten or replace the affected rack section, reset the pinion mesh, and test the gate under load. If your loop detector or keypad is also dead, we’ll diagnose that in the same visit. Most slide gate rack repairs run $300 – $700 depending on track condition.
Get Your Richland Hills Gate Fixed Today
If your gate is stuck, scraping, or refusing to reverse, call Calder Gate Repair at (903) 417-0793. A live person answers 24/7. You’ll get a straight answer, a live arrival time you can track, and a written price before any work starts. Whether it’s a LiftMaster acting up, a sagging weld on a Baker Boulevard corner lot, or a commercial FAAC operator near Grapevine Highway, we’ll show up ready. That’s the Relay Standard, and it’s how we work in Richland Hills.
Written by Nico Alvarez, Owner at Calder Gate Repair, serving Richland Hills and the Dallas-Fort Worth region.