Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Highlands, TX
If your gate in Highlands won’t open, sags on its hinges, or the opener just hums without moving, Calder Gate Repair can usually have it sorted the same day. Most gate jobs in Highlands run from a simple sensor replacement to rebuilding a rusted post base. We show up with a written price before any work starts, and every repair is covered by our 365-Day Done Right Promise. Call (903) 417-0793 and you’ll get a live person, not a voicemail.
Why Highlands Homes Are Different
Highlands sits along the San Jacinto River, and that proximity to water shapes almost every gate job we see here. The humidity and salt-tinged air work on metal faster than homeowners expect, especially on hinges, post bases, and opener circuit boards that live inside unvented control boxes. We regularly open control panels in Highlands and find corrosion on terminal connections that would still look new twenty miles inland.
A lot of the gate systems here are standalone tube gates or swing gates on pipe posts, and many were installed when the house was built. That means the wiring was direct-buried without conduit in plenty of cases, and after a decade of river-bottom soil shifts and mowing contact, a tiny nick in the insulation becomes a short. Highlands jobs also deal with flat terrain and clay-heavy soil, so a leaning gate is usually a post footing that’s rotated in the ground, not a hinge that failed. We plan repairs around those conditions from the first visit.
The housing stock along Wallisville Road and up toward the river bend skews older and more custom, so gate widths and post spacing are rarely standard. That’s half a day for a box-store kit and an hour for a crew that deals with it every week.
Our Main Highlands Services
Highlands homeowners call us for three things: a gate that won’t close, an opener that’s gone dead, and electrical gremlins somewhere between the two. Each service has its own Highlands page so we can go deep on what the work involves here.
Gate Repair in Highlands
A swinging gate in Highlands takes a beating from wind off the river and ground that shifts with every wet-dry cycle. The typical call is a gate dragging on the ground, a latch that won’t catch, or a post that’s started to lean. We straighten, re-set posts in new concrete where the old footing has failed, and repack hinges before they snap. If you’re not sure whether it’s the gate itself or the motor, start with Gate Repair in Highlands for what we check first and what typical fixes run.
Electric Gate Repair in Highlands
Electric gate problems in Highlands are almost always power, limit settings, or safety sensors that got nudged out of alignment. With the humidity here, corroded wire connections inside the control box are common enough that we check them on every call. If your gate opens but won’t close, or only moves a few inches, the diagnosis is usually straightforward. See Electric Gate Repair in Highlands for the specific failure patterns we see most and what they cost to fix.
Gate Opener Repair in Highlands
When the opener motor runs but the gate doesn’t move, it’s often the drive, the capacitor, or the control board – and Highlands’ humidity accelerates all three. We work on openers from Viking, Ghost Controls, DoorKing, and Elite, and we stock the parts that fail most often so the job doesn’t stall waiting on freight. The page on Gate Opener Repair in Highlands covers brand-level symptoms and typical repair ranges.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Highlands
We’re factory-familiar with nine opener brands, and in Highlands the ones we see most on ranch-style and driveway swing gates are Viking, Ghost Controls, DoorKing, and Elite. We keep common boards, remotes, and safety sensors in the truck, so most opener repairs happen in one visit. Check our brands page for the full roster and what we stock.
Pricing for Gate Company in Highlands, TX
| Service | Typical range in Highlands |
|---|---|
| Gate opener diagnostic | $75 – $125 |
| Limit switch replacement | $145 – $225 |
| Safety sensor replacement | $135 – $215 |
| Capacitor replacement | $110 – $185 |
| Control board replacement | $225 – $420 |
| Remote programming | $65 – $110 |
| Keypad install or replacement | $135 – $245 |
| Hinge repair or replace (per set) | $90 – $215 |
| Gate post re-set in concrete | $210 – $380 |
| Full gate opener replacement | $650 – $1,400 |
In Highlands the things that push a job toward the top of a range are corrosion-related board damage and post footings that have shifted in the clay. Whatever the number, you get it in writing before we turn a single bolt, and the invoice at the end matches the quote you approved.
Neighborhoods We Serve in Highlands
Our crews cover all of Highlands, from the older lots between Wallisville Road and the river to the newer-permit work going in around the east side. Typical response is same-day for most opener and gate failures, and next-day at the latest when a specialty part has to come from our Houston stock.
- Highlands central, including along Wallisville Road
- Riverbank Drive and the surrounding streets
- Areas near Thompson Road and the east boundary
- Homes off East Wallisville Road toward the river
- Smaller clusters along the San Jacinto side of the loop
Service Area – Cities Near Highlands
Our Highlands crews also run jobs in the surrounding area on a regular schedule. We handle gates in Channelview, TX, Baytown, TX, La Porte, TX, and Deer Park, TX. Dispatch and scheduling for Highlands are coordinated from our Houston office; the technicians who arrive at your gate are local to this side of town.
Serving Highlands, TX - Our Local Coverage Area
We’re based in the Highlands area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Highlands
Most Highlands calls get a same-day visit, and we offer 24/7 emergency dispatch. When you call (903) 417-0793, a live person takes the details and sends you a trackable arrival time, not a four-hour window. Urgent jobs like a gate stuck open get priority routing.
Most repairs, including opener swaps and post re-sets, don’t trigger permits in Highlands. If your subdivision has an HOA with gate appearance rules, we can match materials and finish to the original install. We’ll flag any requirement before work starts so nothing slows down the job.
For most common repairs, yes, we’ll give you a range over the phone based on the symptoms you describe. The exact written price comes at the door after a quick diagnosis, and it’s the same number on the invoice. No change orders, no surprises. Call (903) 417-0793 for a free estimate.
If your gate is misbehaving anywhere in Highlands, call Calder Gate Repair at (903) 417-0793. You’ll get a straight answer, a trackable arrival time, and a written price before work starts. We back every gate and opener repair with the 365-Day Done Right Promise, and if something isn’t right, we come back free.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Highlands Customers Say
"Safety sensors realigned. Works fine. Photo eyes were dirty and out of line. Gate now stops when it should."
- Raul A."Booked online. The tech texted his ETA and arrived on time. Gate opener was dead; he replaced the control board and tested the sensors."
- Terry W."Booking was easy and the job was done quickly."
- Seth R.