Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Farmers Branch, TX
Most gate repairs in Farmers Branch run between $150 and $650 depending on what failed, and Calder Gate Repair gives you a written price before any work starts. Farmers Branch is a dense, established city where many homes sit on compact lots with alley-loaded garages and wrought-iron or steel swing gates, and those gates take a beating from North Texas heat, clay soil movement, and the occasional hailstorm. When a gate stops opening, call (903) 417-0793 and a live person answers, day or night.
Why Farmers Branch Homes Are Different
Farmers Branch gate work has its own rhythm, and it starts with the soil. The Dallas County clay under this city expands and contracts hard through wet-dry cycles, which shifts gate posts and throws swing gates out of alignment faster than you’d expect. We regularly see gates that worked fine in April binding by August because the post moved a half inch. That same soil movement stresses hinges, latch hardware, and the opener’s travel path, so a repair here often means correcting the gate’s geometry before touching the motor.
The housing stock matters too. Farmers Branch has a lot of mid-century and 1980s-era homes, many with original gate installations that predate modern safety sensors. Homeowners upgrading openers on those older gates frequently need new wiring runs and photo eyes added to meet current code. And the storms that roll through the Metroplex bring wind loads that flex tall wooden and iron gates, loosening bolts and cracking weld points over time. All of that is normal here, and none of it surprises us.
Our Main Farmers Branch Services
Most calls we get in Farmers Branch fall into three buckets: a gate that won’t move at all, an electric gate that opens but won’t stop or reverse correctly, and a gate opener that runs but doesn’t engage. Each has its own dedicated page below.
Gate Repair in Farmers Branch
A sagging or stuck gate in Farmers Branch is usually a structural problem before it’s a mechanical one, and the soil here accelerates it. We’ll check post plumb, hinge wear, latch alignment, and rack or chain tension, then rebuild what’s loose before adjusting the opener to match. If a weld is cracked or a post has shifted, that gets addressed first so the fix holds. See Gate Repair in Farmers Branch for full pricing and what a typical repair includes.
Electric Gate Repair in Farmers Branch
When an electric gate opens but won’t stop, or stops halfway and reverses, the problem is almost always in the control board, limit switches, safety loops, or the photo eyes. North Texas temperature swings are hard on circuit boards mounted inside metal operator boxes, and Farmers Branch homes with older LoopMaster or Sentex systems see board failures regularly. We diagnose on site and quote the fix before touching anything. See Electric Gate Repair in Farmers Branch for what those repairs involve.
Gate Opener Repair in Farmers Branch
If the opener motor runs but the gate doesn’t budge, or the remote stopped working, you’re in opener territory. We handle capacitor failures, stripped gears, receiver issues, and keypad programming across all the major brands, and we stock the common parts in local vans so most Farmers Branch opener repairs finish in one visit. See Gate Opener Repair in Farmers Branch for a detailed breakdown by symptom.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Farmers Branch
Our techs work on Linear, Viking, Ghost Controls, and DoorKing openers every week in Farmers Branch, and we’re factory-familiar with them, not just aware of them. Vans carry the common boards, remotes, and limit switches for those brands, so many repairs wrap up same visit. See our brands for the full list of what we service.
Pricing for Gate Company in Farmers Branch, TX
| Service | Typical range in Farmers Branch |
|---|---|
| Gate opener circuit board replacement | $250 – $480 |
| Limit switch replacement | $140 – $240 |
| Remote control programming | $75 – $125 |
| Hinge replacement (steel gate) | $180 – $350 |
| Post re-alignment | $200 – $450 |
| Safety sensor (photo eye) replacement | $150 – $280 |
| Weld repair (cracked gate frame) | $120 – $300 |
| Chain or belt replacement | $160 – $320 |
| Full diagnostic service call | $89 – $149 |
What pushes a job toward the high end in Farmers Branch is usually post movement that requires concrete work, or an older gate that needs retrofit safety wiring before the opener can be touched. Your written quote covers the entire job, parts and labor, agreed before we start.
Neighborhoods We Serve in Farmers Branch
We run calls across all of Farmers Branch, and our local crews know the difference between a gate in Valwood with alley access and one off Valley View Lane where the set-back and HOA rules differ. Response time for most non-emergency calls in Farmers Branch is same-day or next morning depending on when you call.
- Valwood
- Chase Oaks
- Mercer Crossing
- Farmers Branch Park
- Brookhaven
Service Area – Cities Near Farmers Branch
Our Farmers Branch crews also cover nearby cities across the metro. If you’re just outside the city line, check our Dallas, TX or Fort Worth, TX pages. We also have coverage in Houston, TX and San Antonio, FL for those service areas.
Serving Farmers Branch, TX - Our Local Coverage Area
We’re based in the Farmers Branch area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Farmers Branch
Emergency calls in Farmers Branch are typically dispatched within 2 to 4 hours, and non-emergency repairs are usually scheduled same-day or next morning. Every technician arrives with a live, trackable arrival time so you’re not waiting on a vague window.
If your neighborhood has an HOA, like many in Farmers Branch do, yes, you may need approval for changes to gate appearance or hardware upgrades. Repairs that restore the existing gate to working order rarely need approval. We can note the work scope for your HOA if asked.
Yes. We cover the entire city of Farmers Branch, from the border with Carrollton down to the Dallas line, including residential and small commercial gates. Scheduling is handled through our DFW metro office, and crews serve Farmers Branch locally.
Need a gate looked at today? Call (903) 417-0793 for a free estimate. A live person answers, and your price is written before any work starts.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Farmers Branch Customers Say
"Swing gate arm replaced and aligned. Got photos of the old part by text."
- Nadia F."Quote came in the app before the visit. No surprise at the end."
- Ginny L."Keypad and remotes reprogrammed in one visit. Paid by link."
- Pauline C.