Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Roanoke, TX
Gate repair in Roanoke, TX centers on one reality: most homes here sit on larger lots with custom drive gates, and when one fails, it traps vehicles or leaves the property open. We’re Calder Gate Repair, the dedicated gate specialist inside the Relay Home Co. family, and we handle everything from a LiftMaster opener that stopped responding to a welded steel gate that’s sagging on its hinges. Most Roanoke gate repairs run $180 to $340 before parts, and we quote every job in writing before any work starts. Call (903) 417-0793 when your gate misbehaves.
Why Roanoke Homes Are Different
Roanoke’s housing stock skews newer than much of the DFW metro, but the gate hardware ages on the same timeline as the Texas sun allows. Summer heat bakes control boards, and the clay-heavy soil in neighborhoods like Fairway Ranch and Trophy Club shifts enough to pull gate posts out of alignment. That combination means we see two failure patterns more often here than anywhere else in our service area: heat-stressed circuit boards inside gate openers, and hinge or post problems caused by ground movement. Clay soil expands when wet and contracts when dry; a gate that swings cleanly in March can drag by August. If you live off Marshall Creek or along Litsey Road, you may also deal with grade changes that put unusual stress on the gate’s low side. We account for all of that before we touch a single bolt.
Our Main Roanoke Services
Roanoke homeowners call us most about two things: a gate that won’t open at all, and an electric opener that runs but won’t move the gate. Here’s how each works in Roanoke specifically.
Gate Repair in Roanoke
This covers the physical gate itself: sagging hinges, bent tracks on slide gates, a gate that scrapes the driveway, or a post that’s shifted out of plumb. On Roanoke’s clay soil, post movement is the recurring villain. We reset, shim, and re-secure posts, then re-hang the gate so it swings or slides true again. If your gate binds near the latch or makes a grinding sound halfway through its travel, this is the page to read. Gate Repair in Roanoke covers the full breakdown, including what we check on the first visit and what typical repairs cost.
Electric Gate Repair in Roanoke
Electric gate repair focuses on the power side: motors, control boards, wiring, safety sensors, and keypads. North Texas storms are hard on outdoor electrical connections, and we regularly replace corroded terminal strips and fried boards after heavy rain. When the gate has power but won’t respond to a remote or keypad, it’s usually a control board or a limit switch, the small sensor that tells the gate when to stop. Electric Gate Repair in Roanoke explains the diagnostic process and what parts we stock on the truck versus what we order.
Gate Opener Repair in Roanoke
Opener repair is narrower: the motor unit itself, the gear train, the remote receiver, and the brand-specific electronics. We work on nine major brands, including FAAC, BFT, Linear, and Viking, and we know which Roanoke installations tend to run which boards. If your opener hums but won’t move, or if the remote only works from ten feet away, the opener is the likely culprit. Gate Opener Repair in Roanoke covers brand-specific issues and what a typical opener repair costs in this market.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Roanoke
We carry parts for the brands you’ll find on Roanoke gates: FAAC, BFT, Linear, and Viking, among others. Common boards and remotes for these four are usually stocked locally, which means same-week turnarounds on most opener jobs. See our brands for the full compatibility list.
Pricing for Gate Company in Roanoke, TX
| Service | Typical range in Roanoke |
|---|---|
| Gate opener diagnostic visit | $89 – $129 |
| Gate opener repair (labor, before parts) | $180 – $340 |
| Control board replacement | $240 – $520 |
| Remote or keypad replacement | $75 – $195 |
| Safety sensor replacement | $120 – $285 |
| Hinge replacement or repair | $95 – $250 |
| Gate post reset or shim | $140 – $380 |
| Track realignment (slide gates) | $110 – $290 |
| Motor replacement | $320 – $625 |
| Full gate re-hang after post shift | $260 – $575 |
In Roanoke, the biggest price driver is usually post movement: when clay soil has shifted a post, the repair involves excavation and re-anchoring, not just a hinge swap. We also see higher parts costs on high-end FAAC and Viking openers than on entry-level units. Whatever the job, you get a written price before any work starts, and that number doesn’t change at the invoice.
Neighborhoods We Serve in Roanoke
We dispatch technicians across all of Roanoke and the immediate surrounding area. Most appointments in the city can be reached within about 60 to 90 minutes of scheduling, and we give you a live, trackable arrival time instead of a four-hour window. Neighborhoods we regularly serve include:
- Fairway Ranch
- Trophy Club
- Marshall Creek
- Litsey Road area
- Roanoke town center
Service Area – Cities Near Roanoke
Calder Gate Repair serves Roanoke and the surrounding DFW cities. If you’re just across the city line, we also cover Flower Mound, TX, Southlake, TX, Argyle, TX, and Keller, TX. Dispatch is coordinated from our Dallas-Fort Worth office, and our crews serve Roanoke locally throughout the week.
Serving Roanoke, TX - Our Local Coverage Area
We’re based in the Roanoke area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Roanoke
Most Roanoke appointments are reached within 60 to 90 minutes of your call. We dispatch a live, trackable arrival time, so you’re not waiting on a vague window. Call (903) 417-0793 and we’ll tell you exactly when we’ll be there.
Most Roanoke HOAs regulate gate appearance but not functional repairs like opener replacement, hinge work, or sensor fixes. If your HOA requires approval for a full gate replacement, we can provide the written estimate and specs they typically ask for.
We cover all of Roanoke plus nearby cities including Flower Mound, Southlake, Argyle, and Keller. Our crews serve the Roanoke area locally, with scheduling and dispatch handled from our DFW office. Call (903) 417-0793 to confirm your address and get a free estimate.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Roanoke Customers Say
"Quote came in the app before the visit. No surprise at the end."
- Ginny L."Keypad and remotes reprogrammed in one visit. Paid by link."
- Pauline C."Good job on the motor. Part took a few days to arrive, but the updates came by text."
- Oscar J.